Sunday, August 24, 2008

Receiver hitch mounted basket


This receiver hitch mounted basket is one of the most useful accessories I have ever purchased for any of my SUV's. I have used this to haul many deer from the field back to camp or the processor. I also use it to haul gear to the deer lease. I have even used it quite a few times around town to haul plants and other messy or oversized items.

Gun Rack


I bought this gun rack from Cheaper Than Dirt via the internet. It cost about $60. and is sturdy as hell. It mounts with a floor plate and the rack attaches with 6 wing nuts making it readily removable. It is also adjustable forward and back so you can get the angle of mounting you want.

Adding snaps to the top




While the top was in great shape when I bought the Scout, in fact it appeared virtually new, it fastened down with a series of rubber strips which were very difficult to secure (almost impossible in cold weather). So I asked the guys at ASM Auto Uphosltery to replace the rubber strips with metal snaps. It definately secures much quicker and easier now.









Reupholstery seats

New upholstery...

I kept the seat frames that came with the Scout since they were in good shape... I'm not sure if they are original or not? But the vinyl needed replacing so I went to ASM Auto Upholstery in Dallas. I wanted something inexpensive, water proof and durable. They recommended a heavy duty, thick marine grade vinyl and since the interior of the Scout is now all black and white, we selected a black vinyl. They knocked out the work in less than a week and they did a great job. The cost for both front seats and the rear bench was under $700.


New exhaust system







I took the Scout into Ken's Muffer's on Northwest Highway near Bachman Lake. You can't miss the giant "Muffler Man" out front - it's virtually a Dallas icon. Ken's has been in business for a long time and they have a reputation for doing a great job for a fair price. They took a good look and decided that a complete system was in order... all new pipe front to back and a new muffler. Now the Scout sounds and runs great. And no more breathing exhaust fumes from a leaky tailpipe!














Tuesday, July 22, 2008

Chip's Auto Repair

Chip's Auto Repair

These are the guys who spent the last 6 months refurb'ing my Scout... John on the left and Chip on the right.

Chip Healey has been repairing vehicles in this area for over 15 years and has established a personal base of over 500 loyal customers - myself now included! They put a lot of sweat and heart into this project and I cannot thank them enough. During the many months of working with these men, it became very evident to me that they genuinely love what they do for a living and it is sincerely not just a job to them. Their work speaks for itself.

And this is not there first Scout either. They have a lot of experience doing build up and refurb on Scouts!

Chip's Auto Repair is located at:
2016 Keller Springs Road
Building 1, Suite 100
Carrollton, Texas
(located behind the CVS Pharmacy)
Phone 214-676-7802
Just ask for Chip Healey!
Posted by Picasa

New cover


I just received my new vehicle cover from Covercraft and I am happy to report that the fit is great and I am very pleased with the overall quality and workmanship. Covercraft was a pleasure to work with. They have a simple but detailed form covering every vehicle dimension which is rquired to get the fit right, and it's downloadeable from the internet. They did happen to already have all the stock Scout dimensions on file for my vehicle although the cover they made for me did require some customization since my Scout has very large oversized bumpers front and back. But it was evidently no problem at all for the Covercraft folks. They knocked it right out and I received my cover in about a week or so after I placed the order. They even had a special running for this popluar durable fabric which made the deal all that much sweeter. I got a great quality cover at a great price and it was easy!
Posted by Picasa

Monday, July 7, 2008

Trailer pics

This is the trailer I haul my Scout with. I just added the storage box up front to hold tie down straps, chains, etc. I already had the box and attaching it was a simple enough task. The only extra work I had to do was move the swing down trailer jack forward to clear room on the tongue for it. I also recently had Chip add brakes to the trailer so it's much safer to tow the Scout now.




Posted by Picasa

Sunday, July 6, 2008

New gas cap


The gas cap that came with my Scout was pretty battered up and didn't seal all that well any longer so I ordered a new one from scoutparts.com . Now it's looking good as new and I have good tight seal again.
Posted by Picasa

Saturday, June 28, 2008

Original hubcaps


My Scout came with these hubcaps and I assume they are the originals as I doubt any of the previous owners would have gone to the trouble to replace them had they been lost. I had the wheels repainted black and I was initially going to go with that look but now that I have the hubcaps back on I think they give the Scout a more classic look.

Posted by Picasa

Thursday, June 26, 2008

Floorboard drain holes

Chip and John drilled holes in the floor then filled them with these expandable plugs to facilitate easy cleaning of the interior. I can basically now just hose it out...

The entire floor and all the inside walls, including the lower half of the door panels, are covered with a sprayed-in polyester liner. This provides a very durable, easy-to-clean surface.

Posted by Picasa

Mounting new emblems

Rather than replacing the original speed clips which attached to pegs on the back of the emblems (the original emblems were missing from my Scout when I purchased it) I found this 3M plastic and emblem adhesive at the local Napa Auto store. It works great and the new refurb'd emblems look good as new and give the Scout really nice finished look.


Posted by Picasa

Identify That Scout - Scout Model Year Changes

This a handy guide to identifying your Scout year model...

GC

Identify That Scout - Scout Model Year Changes
By Howard Pletcher

Here are some of the changes that occurred from year to year that will help identify each year of Scout II production. There are some other changes that could be noted, but these are ones that I could positively identify. Note that the model year change usually took place around July of the previous year.
1971. First production 4/19/71. Grille shell painted body color (pre-production units were dark gray) and had 3 horizontal slots. 4-196, 6-232, 6-258, V-304, and V-345 engines, T13/14 3speed, T44/45 4speed, T-39 Warner Gear Automatic tr ansmissions. FA-13 Dana Model 30, FA-44 Dana Model 44 Front axles, RA-18 standard and RA-28 Trac-loc Dana Model 44 Rear Axles. 3.31, 3.73, and 4.27 ratios available. Spring ratings 2200# and 2400# front, 2000#, 2000#HD, and 2500# progressive rear. Bla ck vinyl upholstery and dash standard, blue, sage, black, and red nylon optional.
1972. Grille shell changed to silver, rear seat back angle revised to be more verticle. 6-232 engine dropped.
1973. Grille changed to vertical bars, divided in the center, painted body color, thin chrome "pencil" trim around halves of grille. Vertical ribs added to rear inner panels to stop drumming (running change during year). 4-196 engine dr opped, T-407 Chrysler automatic transmission and TC-143 chain drive transfer case offered. Finned front brake drums in front, optional console and clock. Spring ratings 2500# front and 2700# rear available. Merchandising kits for optional stripes appea red.
1974. Chrome overlay over the 1973 vertical bar grille, square mirrors replaced round. Dual exhaust standard with V-8s. FA-44 standard (but FA-13s were substituted on some vehicles due to a shortage of FA-44s). Disk brakes standard on front with 6" rims replacing the 5.5" to provide caliper clearance. 7" chrome wheels and radial tires offered. Front sway bar standard on 1/1/97. White and woodgrain vinyl side applique panels, and a wide white stripe applique at the bottom of the side s available.
1975. Same grille as 74, but with square headlight bezels added. XLC (Xtra Load Capacity) model designations introduced to avoid emission requirements of lighter duty models. Spring ratings of 3100# and 3200# on front, and 3100# and 310 0# progressive rears offered to reach the required 6100@ GVW rating. 4-196 engine reintroduced in place of 6-258. V-345A engine with some lighter-duty features replaces standard V-345. 3.07, 3.54, and 4.09 axle ratios offered. T-427/428 4 speeds and T -332 3 speed with synchronized low gears introduced. Tanbark vinyl interior standard, optional Saddle, Tanbark, Parchment, Wedgewood Blue, and Ivy of woven vinyl offered. Woodgrain dash trim, "Mid-high" back bucket seats (from the Chevette), optional lo w-profile rear view mirrors, stainless steel, non-adjustable whip radio antenna (mid-year), 4WD Engaged light, bezels, padded covers on console and rear inner quarters added. Numerous items such as chrome bumpers and locking hubs standard. Side applique was continous rather than seperate panels.
1976. Grille is divided into 3 sections with horizontal bars in each section, chrome overlay standard. Traveler and Terra added. 100" pickup dropped. Non-turbo Nissan diesel offered. New side applique: Rallye, white, cork, and feather s. Rear springs re-arched to make rear sit level. "Selectro/Dualmatic locking hubs optional. Steel fuel filler pipe in place of plastic, Spirit and Patriot models built.
1977. 2 horizontal slots in grille with 3 small verticle supports. Optional interiors now Saddle or Parchment vinyl and Tanbark or Wedgewood Blue nylon. 1/3-2/3 bench seat now folds on driver's side. Black Warn Lock-O-Matic hubs with s pring loaded manual operation available. SSII introduced 3/77. 8" white spoke wheels with hardened front spindles offered.
1978. Same 2 slot grille used, but support bars are blacked out. New arm rests (from S-Series), Prestolite "Common Base" distributor with integral electronic ignition used after 10/6/77. 3.73 rear axle ratio optional, Tiempo All-season tires optional, plastic tail light and marker light housings after 2/78. Lock-O-Matic Hubs have steel ring in manual section replacing plastic 3/6/78. New appliques: Rallye has "hash" marks, white and woodgrain with pattern that varies from front to rea r, stripe is now thin strip between markers. Rustproofing improvements are gradually being made.
1979. Few or no visible exterior changes. New interiors: Black standard, Sierra Tan or Black winylv and Russet or Highland Blue fabric in Custom interior, bolsters on high-back bucket seats, engine-tuned trim on dash, carpeted door panel s with map pockets and carpeted rear quarter panels, vinyl headliner, redesigned console lid with cup holders. Catalytic convert/no-lead fuel required, Thermoquad 4-barrel carb on V345A. TC-143 single speed transfer case dropped. Terra not available as 4x2. Restricted option list for 4-196 engine due to emission certification requirements, Engine oil cooler available. Selective Edition model with Brown or Black paint, SSII grille, gold spoke wheels and Tracker tires, and a gold side strip built.
1980. New plastic grille shell with square headlights. Standard window frames and bumpers are black instead of gray. New caster/camber specs for front axle (2.5 degrees and .5 degrees) to improve front tire wear. 15" styled steering wh eel is standard, Nissan Turbo Diesel offered, polycast wheels, 2.72, 3.31, 3.54, and 3.73 were axle ratios, TC-146 Dana 300 transfer case, new air conditioning housing which is full width of dash (introduced during '79 model year). New applique: Rallye, Waves, Spear, and Flare styles. 85mph speedo head in place of 100mph, Scout decals on rear quarters, stick-on vinyl side trim in place of stainless steel, power steering is standard, black manual locking hubs with Scout id, no T-332 or T-427 deep low tra nsmissions in Traveler, Tartan Blue is blue interior color, brushed satin trim on dash.

Tom's Notes:
T-427/428 4-speeds introduced in '75 were the T19, close and wide gear boxesprior to '75, T-18 non-sync 1st gear close ratio offered.6-232 and 6-258 were AMC motors.T-407 Auto tranny is the Chrysler TorqueFlight 727. Standard Transfer case, TC-145, is a Dana 20.

Hilfiger Scout ad


Note the old Scout they used for this Hilfiger ad out on the salt flats. It looks a lot like mine... same paint color, same mirrors... not sure about the year model?
GC

Monday, June 23, 2008

The 196 Inline 4-cylinder

I found this little article today about the IH 196 while browsing. Kinda interesting so I thought I'd copy it over... GC


Publish date: Oct 1, 2005 By: Alain Hoffmann

This is actually half of the 392 V-8 and at first glance it looks strange enough. Imagine an V-8 where you cut the left half off. It sits there in this enormous engine bay, leaning to the right and looking innocent enough. But don't be fooled, it weights 476 pounds dry and 545 pounds with standard accessories which makes up for a huge chunk of iron for any suspension and frame.

4-196 Technical Data
Bore = 4.125
Stroke = 3.656
Compression = 8.02:1
Power =
86HP@3800rpm
Torque =
157Lb.Ft.@2200rpm
Firing order = 1-3-4-2
Spark plug gap = .030 inch
Initial timing set = TDC*
Idle Speed = 525-575rpm
Max. speed = 4000rpm*TDC (Top Dead Center), timed on #1 cylinder, all vaccum lines off and plugged.


Refer to smog sticker under hood! The four isn't the greatest motor ever made, especially in front of the Chrysler TorqueFlite Automatic. It just plainly lacks power to pull an 3500+ pounds vehicle. It's strong side is it's durability which is no wonder if you consider that it's indeed an 392 that only puts out half the power it's designed for. 300000+ miles should be possible between rebuilts if you change oil regularly.For those in need of more power: The engine is very restricted on it's intake and exhaust side as well as handicaped by the torque- oriented cam and advance curve. A first step would be some slight head work with deburring and light polishing. But don't expect too much from this. Than you can get an exhaust header that will also slightly boost performance. But you're still limited by the small carb if you don't find a way to replace it. The single most rewarding tuning stage in most engines is changing the cam. This will boost performance and make for a much more lively engine. Add to this an recurved distributor and you should end with something around 110HP.The most cost-effective change is surely the swap to an larger V-8 out of the IH-line. These are direct bolt-ons. In fact most parts of the 392 are virtually identical to the 196 with the exception of crank, flywheel and intake manifold. Good V-8 engines can be had for $500.

Sunday, June 22, 2008

Wire harness problem

When I picked up my Scout from Chip for the first time after it's major refurb,. I only managed to get a couple miles down the road before I immediately had engine problems and I had to call in a tow truck to haul me back to Chip's place. With zero hours on the new engine (17,130 on the odo -- that's probably 117, 130 I imagine...), it coulda been any number of things. But Chip and John figured it out rather quickly. The bulkhead connectors had degraded to the point where the wire harnesses would not stay connected. Chip and John were able to quickly rig up a couple of cable ties to hold everything securly in place and I was back on the road in an hour. This fix seems to be working well for now anyway. There are also some burned wires behind the dash and under the hood, so I have placed an order with Super Scouts Specialists for new main dash and engine harnesses as well as new bulkhead connectors. The new harnesseses and connectores should alleviate future problems in these areas. There are also headlight and tailght harnesses on Scouts but all these wires have pretty much just been redone so I don't think they are worth replacing again at this time.

By the way, Super Scout Specialists do these harnesseses the right way. They create them from scratch on pegboards from the original factory blueprints with all the correct connectors, etc. And all the wires are cut to the exact correct length, same as originals. You don't jut get a big bag of assorted connectors and a large spool of wire like most of the other guys out there sell. But the down side is that it does take them 8 to 10 weeks to complete orders for these.

Fuel filters

We were of course concerned about the condition of the fuel tank so Chip and John initially drained out all the old gas, the flushed it several times with new gas before filling it up They then installed a new fuel filter which trapped quite a bit of cast off sediment right away. It took a bit longer for the second filter to fill up with trash. We are now on the third filter and it seems not to be collecting much dirt at all anymore. So the old tank appears to okay for now.
Posted by Picasa

Securing and installing batteries

I upgraded to a no-maintenance gel battery for the primary and we added a secondary dedicated deep cycle gel battery to power the winch. This secondary battery also has a trickle charge system to keep it fully ready at all times. The new battery required the addition of a new tray and clamp on the opposie side of the engine compartment. The old battery just needed a new clamp as the tray was still in decent shape. The guys ran all new wiring to the batteries.
Posted by Picasa

Scout II Emblems

I found these "Scout" and the "II" emblems on ebay for about $28.00 plus shipping. They were repainted by the seller and they look great. All I did was spray them with clearcoat for some added protection and a little more gloss. Now I just need the "International" emblem for the tailgate. I'll keep looking on ebay...
Posted by Picasa

IH emblems

All the original emblems were gone on the Scout when I aquired it. I have been looking for replacements but good ones in good condition are hard to find (like everything else for a 32 year old vehicle). Scoutparts.com does offer a complete set of replacements but at the hefty price of $296.00 I thought I'd continue my search. I found a pair of "IH" emblems on ebay; the chrome was in decent condition and they still had their mounting pegs, but the paint was pretty far gone. But for $10.00 plus shipping, I figured I could make them work. I bought a can of International red spray paint for a few dollars and I already had some good black paint. I then carefully masked off the emblems in stages and sprayed them. I gave them a clear coat finish for added protection. The final results are pretty good I think, especially for the price.
Posted by Picasa